[email protected]

ALLOY 400 DATA SHEET - jacquet.biz

//// A large percentage of Alloy 400 is put into service without a final heat treatment. This is done to increase the strength of the material. //// Alloy 400 exhibits excellent cold forming characteristics normally associated with chromium nickel stainless steels. The alloy has a lower work hardening rate than T301 or T304 stainless steel and can Dissimilar Materials Weldability Concepts - EWIStainless Steel Carbon or Carbon or Low Alloy Steel Low Alloy Steel Weld Metal Buttering Layer of Pure Ni Copper Steel Electrode Copper Carbon or Low Alloy Steel Joint Parts Material Thermal Exp./Cont Coeff. (1/K) x 10-6 YS (ksi) UTS (ksi) Stainless Steel 316 L 19 42 84 Weld Metal 308 L 19 29 84 Buttering 309 L 19 40 95

Feasibility of GTA method on welding of alloy 400 and 304

The behaviour of alloy 400 and SS 304 weldments subjected to the elevated temperature media at 600oC is evaluated. If the choice of filler wire and welding process is not fit, few weld defects like segregation, phase development, dilution and cracks will develop in the weldment. HASTELLOY- C-276 alloy Welding DataTorches with gas diffuser lenses provide the optimum gas coverage. Post-weld stress relieving in the 1200°F (650°C) range is not recommended for HASTELLOY C-276 alloy. If required, solution heat-treatment of this material is accomplished at 2050°F (1121°C) for an appropriate time followed by a water quench or rapid air cool (depending on Investigation on the Formability of Tailor Welded Blanks Tailor welded blanks had been widely used in automobile industries. In this paper, the formability of tailor-welded blanks with curved seams had been studied in experiments, and compared with that of tailor-welded blanks with straight seams. For tailor welded blanks with curved welded seams, the effects of thickness ratio on the limited forming height are the same under various welded seam

VCR Metal Gasket Face Seal Fittings Weld Fittings

Weld Fittings. 2. 3 Contents VCR Metal Gasket Face Seal Fittings Technical Data, 4 Typical VCR Assemblies, 5 Glands, 6 Bodies, 11 Welded Assemblies, 17 Nuts, Caps, and Plugs, 18 High-Flow Connections, 20 Gaskets, 22 Flow Restrictors, 24 SS-4-VCR-A1-400 SS-4-VCR-A1S-400 3/8 1/2 SS WELDING HARDOXStainless steel welding consumables Consumables of austenitic stainless steels can be used for welding all Hardox products, as shown in Table 2. They allow welding at room temperature 5 20°C (41 68 °F) without preheating, except for Hardox 600 and Hardox Extreme. Weldability of Materials - Nickel and Nickel Alloys - TWI

  • Material TypesWeldabilityFiller AlloysImperfections and DegradationThe alloys can be grouped according to the principal alloying elements. Although there are National and International designations for the alloys, tradenames such as Inconel and Hastelloy, are more commonly used. In terms of their weldability, these alloys can be classified according to the means by which the alloying elements develop the mechanical properties, namely solid solution alloys and precipitation hardened alloys. A distinguishing feature of precipitation hardened alloys is that mechanical propertieWhich stainless rod needed to weld 409 stainless?Oct 21, 2008 · Do not know the operating temp in the area of the weld repair but 400 series SS should always be PWHTed and a local with a torch would probably work just fine. By Shane Feder Date 10-23-2008 00:04 NMWelding, First choice is 409 Second is 410NiMo Third is 309 As the others have suggested your 309 will be fine for a touch up weld, Cheers, Shane

    Weldability of Stainless Steel The Metal Press by

    The Weldability of Stainless Steel. Known for its corrosion resistance and wide range of uses in food handling, cutlery, and many other applications, stainless steel is one of the most popular metals in use today. The dozens of alloy variants make welding stainless steel more complicated than welding traditional carbon steel. Welding of Ferritic / Martensitic Stainless Steels - TWIAn alternative is to weld with austenitic stainless steel fillers, type 309 for example, but the weld may then not match the tensile strength of the ferritic steel and this must be recognised in the design of the weld. Nickel based alloys may also be used; alloy 625 for instance, has a 0.2% proof strength of around 450MPa; and will give a Welding of Stainless Steel and Other Joining MethodsComparison of Welding Characteristics of Type 304 Stainless Steel with Carbon Steel Carbon Steel Type 304 Remarks Melting Point 2800 2550-2650 Type 304 requires less heat to produce fusion, which means faster ºF Approx. welding for the same heat or less heat input for the same speed.

    Stainless Steels Welding Guide - Lincoln Electric

    post weld heat treatment to soften and toughen the weld. 3.3 AUSTENITIC STAINLESS STEEL The austenitic stainless steels contain 16-26% Cr, 8-24% Ni + Mn, up to 0.40% C and small amounts of a few other elements such as Mo, Ti, Nb (Cb) and Ta. The balance between the Cr and Ni + Mn is normally adjusted to provide a microstructure of 90-100%