ASTM A572 A high-strength low-alloy steel plate that is utilized in a variety of structural applications. This specification is produced in Grades 42, 50, 55, 60 & 65, the grades representing the yield strength. Plates that are 4 and thicker are made to a 42 KSI yield, although material can be modified to reach the 50 KSI min yield. ASTM A572 / A572M - 12 Standard Specification for High 1.3 Specification A588/A588M shall not be substituted for Specification A572/A572M without agreement between the purchaser and the supplier. 1.4 The use of columbium, vanadium, titanium, nitrogen, or combinations thereof, within the limitations noted in Section 5, is required; the selection of type (1, 2, 3, or 5) is at the option of the
1.1 This specification covers five grades of high-strength low-alloy structural steel shapes, plates, sheet piling, and bars. Grades 42 , 50 , and 55  are intended for riveted, bolted, or welded structures. Grades 60  and 65  are intended for riveted or bolted construction of bridges, or for riveted, bolted, or welded construction in other applications. ASTM A572 HSLA Steel ::MakeItFromMay 30, 2020 · ASTM A572 HSLA Steel. ASTM A572 steel is an alloy steel formulated for primary forming into wrought products. It has a very low base cost among wrought alloy steels in the same category. In addition, it has a moderately low electrical conductivity and a fairly high thermal conductivity. The properties of ASTM A572 steel include five common ASTM A572 Steel Plate - A572 Grade 42, 50, 55, 60, 65 A572 is the standard specification for high-strength low alloy columbium-vanadium structural steel. Lists five chemical recipes and five different mechanical property ranges for plate products (grades 42, 50, 55, 60, and 65). Relatively wide chemical and property ranges. Grade 50 high volume.
1.1 This specification covers five grades of high-strength low-alloy structural steel shapes, plates, sheet piling, and bars. Grades 42 , 50 , and 55  are intended for riveted, bolted, or welded structures. Grades 60  and 65  are intended for riveted or bolted construction of bridges, or for riveted, bolted, or welded construction in other applications. Datasheet for Steel Grades Carbon Steel A572 GrA572 Gr.50 Mechanical Properties Tensile strength 231-231 b/MPa Yield Strength 154 0.2 /MPa Elongation 56 5(%) - (%) Akv - Akv/J HBS 235-268 - HRC 30 - A572 Gr.50 Heat Treatment Regime Annealing Quenching Tempering Normalizing Q & T A572 Gr.50 Range of products Product type Products Dimension Keeping tabs on current ASTM specifications ARE YOU ing ASTM A572 Grade 55, 60 or 65, ASTM A529 Grade 55, ASTM A514 Grade 90 or 100 or ASTM A852. Structural plates with atmospheric corrosion resistance (weath-ering characteristics) can be obtained by specifying ASTM A588 Grade 42, 46 or 50. These and other material specifications applicable to structural plates are shown in Table 2. Structural Bars
2015-2016 Plate Steel Specification Guide Page 5 ASTM Specifications continued SPECIFICATION A283 Grade C A283 Grade D A285 Grade A A285 Grade B A285 Grade C Type of Steel Carbon Carbon Carbon Carbon Carbon Requirements for Delivery A6 A6 A20 A20 A20 Tensile Strength (ksi) 55/75 60/80 45/65 50/70 55/75 Yield Strength (Min. ksi) (Yield Point SPECIFICATIONS - DEL METALSSpecifications covering welded structures and should be adequate to avoid weld cracking. However, 380W* 55W* A572 Gr.55 HSS - - 16 5/8 400W 60W A572 Gr.60 1 20 3/4 - - 480W 70W A572 Gr.70 1 14 1/2 - - 260T 38T A36 KFG 5 100 4 - - 300T 44T A572 Gr.45 KFG 5 100 4 - - 350T 50T steelwise - AISCcan be obtained by specifying ASTM A529 Grade 55, ASTM A572 Grades 55, 60 and 65 or ASTM A913 Grades 60, 65 or 70. Atmospheric corrosion resistance (weathering charac-teristics) can be obtained by specifying ASTM A588 Grade 50. These and other material specifications applicable to M-shapes and S-shapes are shown in Table 2-4. Channels.
Gangsteel Grade :A572Gr55. Specification:Thickness 8mm-200mm, Width:1500-4020mm, Length:3000-27000mm. Standard:ASTM A572 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel. Approval By Third Party